We earn a commission if you buy through our links, at no extra cost to you.

Product profile

Anycubic Kobra S1 Combo: Specs, Pros & Cons

Anycubic Kobra S1 Combo explained: enclosed CoreXY, ACE 2 Pro four-color system with drying, 608 °F hotend, noise figures and who should pick it.

By the Best 3D Printers editorial team Published
Anycubic Kobra S1 Combo

Anycubic Kobra S1 Combo

A mid-range enclosed multicolor printer for people who care about dry filament. It does not top the Bambu Lab picks on polish, but built-in drying and a capable hotend make it a solid alternative.

What we like

  • Fully enclosed CoreXY with a 9.8-inch (250 mm) cube build volume and four-color ACE 2 Pro included
  • ACE 2 Pro can dry filament up to 149 °F (65 °C) while printing, which is rare at this tier
  • Listed noise of 46 dB in standard mode and 44 dB in quiet mode, plus an AI spaghetti detection feature

Drawbacks

  • Camera is a standard 480P unit, lower resolution than premium rivals
  • 608 °F (320 °C) hotend is below the 662 °F (350 °C) of some rivals, and TPU only works in single-color mode
  • The ACE 2 Pro is louder when drying, at 55 dB by Anycubic's own figure

The Anycubic Kobra S1 Combo is the enclosed multicolor printer for people who care about dry filament. It ranks fifth in our list and sits in the mid-range tier. Anycubic’s current combo ships with the ACE 2 Pro, a four-color feeder that dries filament while the printer runs, inside a fully enclosed CoreXY frame with a 9.8-inch (250 mm) cube of build space. It is the closest thing among our picks to a Bambu Lab alternative with drying built into the multicolor unit.

This profile uses Anycubic’s published product page and sets the figures against how people use printers at home. We do not test products, so every number is the maker’s own. Where a figure is missing, we say so. To compare all ten, read our ranking of the best 3D printers of 2026.

Who the Anycubic Kobra S1 Combo Is For

This printer suits someone who wants a full, enclosed, multicolor machine without paying for a premium brand. A hobbyist who prints in PETG and wants dry spools, a family with a spare room, or a maker who wants to expand to more colors later all fit.

It also suits shoppers comparing it against the Bambu Lab P2S Combo. The P2S is the more polished experience; the Kobra S1 sits a tier lower. The trade-off is a smaller ecosystem and a lower-resolution camera, in return for a more modest position in the market.

Key Specs, According to Anycubic

Anycubic’s page lists:

  • Build volume: 9.8 × 9.8 × 9.8 in (250 mm per side).
  • Speed: recommended 300 mm/s, maximum 600 mm/s.
  • Acceleration: recommended 10,000 mm/s², maximum 20,000 mm/s².
  • Nozzle: up to 608 °F (320 °C), standard 0.4 mm, expandable to 0.25, 0.6 and 0.8 mm.
  • Heated bed: up to 248 °F (120 °C), PEI spring steel plate.
  • Leveling: LeviQ 3.0 auto-leveling with Z-offset, pressure advance and flow calibration.
  • Safety and monitoring: power-loss resume, filament detection with auto resume, entanglement detection and AI spaghetti detection.
  • Screen: 4.3-inch capacitive touchscreen.
  • Camera: standard HD, supports 480P.
  • Noise: 46 dB or less in standard mode, 44 dB or less in quiet mode.
  • Weight: about 40 lb (18 kg) for the printer and 8.2 lb (3.7 kg) for the ACE 2 Pro.
  • Size: 15.7 × 16.1 × 19.3 in (400 × 410 × 490 mm) for the printer and 14.5 × 11.5 × 9.3 in (368 × 291.5 × 236.5 mm) for the ACE 2 Pro.

Anycubic also lists a one-year warranty on its 3D printers.

The ACE 2 Pro: Multicolor and Drying

The ACE 2 Pro is the reason to shortlist this printer. Anycubic says it supports simultaneous drying and printing at temperatures up to 149 °F (65 °C), with built-in temperature and humidity sensors. It holds four colors, and the system can be expanded to 16.

Drying while printing is a convenience that most cheap multicolor systems lack. Wet filament is one of the most common causes of stringing, rough surfaces and weak parts, and PETG and nylon absorb moisture quickly. Having the dryer in the feeder means spools stay ready.

Noise is the catch. Anycubic’s footnote says the ACE 2 Pro runs at 48 dB with the door closed and 55 dB with drying enabled, measured at 3.3 feet (1 meter). That is Anycubic’s figure and varies by unit, but it tells you drying is audible. Run it overnight in a spare room rather than next to the couch.

As with every multicolor system, color changes cost filament. Anycubic’s FAQ also says TPU (95A) cannot be used through the ACE 2 Pro for multi-material jobs, so flexible prints are single-color and fed directly.

Materials and Temperature

Anycubic’s FAQ lists PLA, PETG, TPU (95A), ABS and ASA. A 608 °F (320 °C) nozzle covers those comfortably. It sits below the 662 °F (350 °C) hardened nozzle on the Elegoo Centauri Carbon 2 Combo, so if you want to print very high-temperature or fiber-filled engineering filaments, the Elegoo has a higher ceiling on paper. Anycubic’s page does not list a heated chamber, so ABS and ASA rely on the enclosed frame to hold heat.

The 248 °F (120 °C) bed with a PEI spring steel plate helps adhesion, and the spring steel plate flexes so parts pop off easily. Anycubic also lists 0.25, 0.6 and 0.8 mm nozzle options for fine detail or faster, thicker prints.

Setup and Where to Put It

Plan for a machine of about 15.7 × 16.1 × 19.3 in (400 × 410 × 490 mm) plus the ACE 2 Pro, which Anycubic lists at 14.5 × 11.5 × 9.3 in (368 × 291.5 × 236.5 mm). The printer weighs about 40 lb (18 kg) and the box about 55 lb (25 kg), so lift it with two hands or a helper. Choose a stable table with room to open the front door and to route the filament tubes from the feeder. Anycubic’s page also lists LeviQ 3.0 leveling, so you should not need to level the bed by hand, but give the first layer a look on your first print.

Noise, Fumes and Indoor Use

The printer’s 46 dB standard figure is respectable, and quiet mode lowers it to 44 dB, according to Anycubic. With the ACE 2 Pro drying, expect more noise. In either case, a spare room, office or garage corner is nicer than a bedroom.

For fumes, the box includes an activated carbon piece. That helps with odor but does not capture everything. PLA is the easy indoor choice. If you print ABS or ASA, ventilate the room, keep the door closed and do not sleep beside the printer.

Ownership: Software and Parts

Anycubic promotes Anycubic Slicer Next, based on the open-source Orca platform, with presets for different filaments and a multi-plate management system. You can send prints from the touchscreen, the slicer, the Anycubic app or a USB drive. Many users also run OrcaSlicer directly.

Nozzles come in four diameters, and the box includes a nozzle cleaning module, an anti-blocking module and a silicone part for the nozzle. Anycubic lists a one-year warranty and offers a 14-day return window on its store page. Read the warranty terms before you buy and keep your receipt.

Who Should Skip It

  • You want the most polished, mature ecosystem. The P2S Combo has the edge.
  • You need a sharp camera for remote monitoring; 480P is basic.
  • You want fiber-reinforced engineering filaments at high temperatures. The Elegoo’s 662 °F (350 °C) nozzle is the better fit.
  • You are very noise sensitive and plan to leave the dryer running next to your desk.

How It Compares to Its Neighbors

Against the Elegoo Centauri Carbon 2 Combo, the Kobra S1 trades a cooler nozzle and a slightly smaller volume for active drying inside the feeder. Against the P2S, it gives up polish and a stronger camera. For the full picture, see our best 3D printers of 2026.

Final Take

The Anycubic Kobra S1 Combo is a solid enclosed multicolor option with a useful trick: the ACE 2 Pro dries filament while you print. A capable 608 °F (320 °C) hotend, auto-leveling and AI detection round it out. The compromises are a basic camera, louder operation while drying and a smaller ecosystem than Bambu Lab. If dry filament matters to you, it deserves a look.

See price on Amazon

Sources

Frequently asked questions

What is the difference between the Kobra S1 Combo and the older ACE Pro version?

The current combo ships with the ACE 2 Pro, Anycubic's four-color unit that can dry filament. The earlier ACE Pro combo has been retired in the US. Make sure the listing you buy says ACE 2 Pro, since that is the version this profile describes.

How loud is the Anycubic Kobra S1?

Anycubic lists 46 dB or less in standard mode and 44 dB or less in quiet mode. For the ACE 2 Pro, Anycubic says 48 dB with the door closed and 55 dB while drying is on, measured at about 3.3 feet (1 meter). Those are Anycubic's own figures and vary by unit.

Can the Kobra S1 print TPU?

Yes, but only in single-color mode. Anycubic's FAQ says TPU (95A) must be fed directly into the printer and does not work through the ACE 2 Pro for multi-material jobs. The FAQ lists PLA, PETG, TPU, ABS and ASA as supported materials.

How many colors can it print?

The combo starts at four colors with one ACE 2 Pro. Anycubic says the system is expandable to 16 colors, which requires additional ACE 2 Pro units sold separately.

What slicer does the Kobra S1 use?

Anycubic promotes Anycubic Slicer Next, which it describes as based on the open-source Orca platform, with presets for different filaments. Printing methods listed include the touchscreen, slicing software, the Anycubic app and a USB drive.

Do I need ventilation with the Kobra S1?

For PLA, usually good airflow in the room is enough. For ABS and ASA, ventilate properly. Anycubic includes an activated carbon element in the box, which helps with odor, but carbon filtration does not replace fresh air.